Emco Controls A/S
Høgevej 6
DK- 3400 Hillerød
Denmark

Phone +45 4576 94 00
Fax +45 4576 94 01
emco@emco.dk

Emco Controls A/S receives the Gazelle award from the leading Danish business newspaper Borsen in recognition of being one of Denmark's fastest growing companies.

Overview of EMCO DP Elements

In the pdf-file below you will find an overview of the EMCO DP Elements. In it you will find all you need to know about design standards, sizes, installation requirements, accuracy etc.

This is a very handy tool when you design or redesign your pipe system.

Flow Element overview in pdf (3,7 mb)

Related documents:

EMCO ASME Flow Nozzle

E Flow Nozzle

The ASME flow nozzle is calculated and manufactured according to ASME MFC-3M.The ASME nozzle is available in 2 models:

the low Î² nozzle
the high Î² nozzle

The nozzle is made in stainless steel and is for insertion between flanges according to ANSI B16.5.The pressure tappings are foreseen in the pipe section.

EMCO Averaging Pitot Tube Type PITOBAR

EMCO Averaging Pitot Tubetype PITOBAR

PITOBAR averaging pitot tubes are used for flow measurement of liquids, gasses and steam in circular or rectangular pipes or ducts in accordance to the principles of differential pressure and Bernouilli's law.

EMCO Classical Venturi Tube Type KVR

EMCO Classical Venturi Tube type KVR

The venturi tube is in a machined construction or in a welded sheet construction.

Process connection are flanges or weld ends.

The venturi tubes are supplied in carbon steel, stainless steel or exotic materials to suit the process conditions.

The classical venturi tube offers very low pressure loss and requires short inlet lengths.

Venturi Tube Type KVR is used in flow measurement of steam

EMCO ISA 1932 Nozzle Type DES

EMCO ISA 1932 Nozzle type DES

The ISA 1932 nozzles are produced with 2different pressure tapping arrangements:

type DES with single pressure tappings
type DRS with annular chambers

The ISA 1932 nozzle offers high degree of resistance towards wear and abrasive fluids including high pressure steam.In sizes up to DN 500 (20”).

EMCO Meter Runs Type MSRS & MSRF

EMCO Meter Runs type MSRS & MSRF
EMCO meter runs with orifice plate are manufactured in sizes from DN 10 (3/8”) to DN 50 (2”).With weld ends (type MSRS) or flanges (MSRF).The meter run is made from calibrated pipe for high accuracy.Meter runs with honed pipes are available for even higher accuracy.

EMCO Orifice Plate Type MEGL

EMCO Orifice Plates type MEGL

EMCO orifice plate is a machined construction with single pressure tappings especially developed for use with clamp type flanges.

For use with high pressure and temperature applications such as feed water flow measurement in power plants.

Calculation and materials are fully documented.

EMCO Orifice Plates Type ISB/1, ISB/2 & ISB/3

EMCO Orifice Plates type ISB/1 & ISB/2

EMCO orifice plates for insertion between orifice flanges according to ANSI B 16.36 with RF or RTJ facing.

Material in stainless steel as standard, others on request.

The plates are calculated according to ISO 5167, ASME MFC-3M or other international standards.

EMCO Orifice Plates Type MEF, MEF/2 & MEF/5

EMCO Orifice Plates type MEF & MEF/2

EMCO orifice plate type MEF with single

pressure tappings for insertion between

RF or RTJ flanges.

The orifice plate is the monobloc type

with incorporated corner pressure

tappings.

The plate is normally in stainless steel,

but for corrosive applications more exotic

materials are available.

EMCO Orifice Plates Type MES & MRS

EMCO Orifice Plates type MES & MRS
EMCO orifice plate is an all welded construction with single pressure tappings (type MES) or annular chambers (type MRS) especially developed for high pressure and temperature applications, such as feed water flow measurement in power plants.Calculation, materials and welding is fully documented

EMCO Orifice Plates Type MRK

EMCO Orifice Plates type MRK
EMCO orifice plate type MRK with carrier rings and with annular chambers. Can be supplied with mating flanges, bolts, nuts and gaskets. Condensing pots are included for steam flow measurement.

EMCO Short Venturi Nozzle Type VRF

EMCO Short Venturi Nozzle type VRF

The short form venturi nozzle has annular chambers.The venturi consists of 2 main parts: a cast liner and a fabricated pipe section.Available in all castable materials.Flange connection according to DIN or ANSI standards.Sizes from DN 150 (6”) to DN 500 (20”).

EMCO Venturi Nozzle Type VES

EMCO Venturi Nozzle type VES

The venturi nozzle type VES with single pressure tappings is supplied with weld ends. The venturi nozzle is used in high pressure/temperature applications in power plants. The venturi nozzle is supplied with condensing pots for steam flow measurement.

EMCO Welded Sheet Venturi Tube Type KVR & FKVR

EMCO Classical and Rectangular Venturi Tubes in Welded Sheet type KVR & FKVR
The venturi tube is in a welded sheet construction, typically for low air flow measurement in large size pipes and ducts.Pressure tappings may be the single pressure type or (as shown) 2 x 4 tappings externally connected with annular rings.The venturi tubes are supplied in carbon steel, stainless steel.